S-Panels Idaho · Reroof Savings Guide

Reroofing? Add insulation with nailbase panels, and find help paying for it

A reroof is the one time your roof deck is bare. S-Panels nailbase panels, rigid foam insulation bonded to a nailable OSB face, go down over the existing deck before the new roofing. This guide lists the rebates, tax breaks and loans in Idaho, Utah, Wyoming and Montana, and says plainly how well each one fits a nailbase reroof.

Last checked: November 10, 2026. Programs change without notice. Get the program's answer in writing before you sign a roofing contract.


Where nailbase makes sense

Strong candidates

  • Vaulted and cathedral ceilings, where there is no attic to blow insulation into
  • Story-and-a-half homes, A-frames, log and timber-frame homes
  • Low-slope and flat roofs on homes, shops and commercial buildings
  • Any roof whose rafter bays are already full and still under-insulated

Think twice

  • A roof over a vented attic. Insulation above the deck does little while outside air still moves through the attic below it. The attic has to be converted to an unvented design first, or it is cheaper to add insulation on the attic floor.
  • Rocky Mountain Power's installation manual says the same thing: no exterior roof insulation over ventilated cavities.

Nailbase R-values

Every panel is 1 lb. EPS foam with one layer of 7/16" OSB. Foam thickness matches lumber and I-joist sizes, from 2" to 11-7/8", so the panels frame in with standard material at the roof edges. Programs compare the rated R-value against their minimums, so use that column on applications.

Foam thickness Rated R-value (75°F) Cold-weather R-value (40°F)
2" R-8.2 R-8.8
3-1/2" R-14.0 R-15.1
5-1/2" R-21.7 R-23.4
7-1/4" R-28.4 R-30.7
9-1/4" R-36.1 R-39.1
9-1/2" R-37.1 R-40.1
11-1/4" R-43.8 R-47.4
11-7/8" R-46.2 R-50.0

Calculated from the typical tested values our foam supplier publishes for ASTM C578 Type I EPS, R-3.85 per inch at 75°F and R-4.17 per inch at 40°F, plus R-0.5 for the OSB. The nailbase adds to whatever insulation is already in your roof.

At a glance: how each program fits a nailbase reroof

Program Where Nailbase fit
Idaho income tax deduction ID homes built or permitted by Jan 1, 2002 Good fit
Idaho Power building shell incentive ID businesses and farms with electric heat Good fit
Idaho Falls Power insulation rebate or 0% loan ID homes on Idaho Falls Power with electric heat Good fit
Utah C-PACE financing UT commercial and multi-family Good fit
USDA REAP Farms and rural businesses, all four states Fits, grant window closed
Rocky Mountain Power Wattsmart Homes ID, UT Ask first
Enbridge Gas ThermWise UT, WY, southeast ID Ask first
NorthWestern Energy insulation rebates MT homes and businesses on gas Ask first
Idaho State Energy Loan, Avista ID homes Ask first
Electric co-ops: Fall River, Lower Valley, Flathead Electrically heated homes in ID, WY, MT Ask first
Montana DEQ energy loan MT Only with solar or similar
Federal 25C, 179D, 45L credits All Ended

Why so many say "ask first": most utility rebates were written for blown-in attic insulation. They call for a finished R-49 and do not say whether rigid insulation above the roof deck counts toward it. Those programs decide case by case, so the answer has to come from them before the work starts.

Before you sign a roofing contract

  1. Call the program first. Tell them it is rigid insulation above the existing roof deck during a reroof, give the R-value being added and what is in the roof now, and ask for approval in writing.
  2. Get any loan approved before work starts. The Idaho state loan and the Idaho Falls Power loan do not cover work already done.
  3. Ask for an itemized invoice. The nailbase panels and their installation should be listed apart from the shingles or metal. Rebates and the Idaho deduction only count the insulation.
  4. Keep the paperwork. Square footage, starting and finished R-values, dated invoices and photos of the deck before it is covered.
  5. Mind the deadline. Applications are due 90 to 180 days after the job, depending on the program.


We supply the R-value and square footage of every nailbase order for your application

Federal programs (all four states)

USDA Rural Energy for America Program (REAP)

Farms, ranches, and rural small businesses

GRANT WINDOW CLOSED

  • Grants cover up to 25% of total project cost. Energy efficiency grants run from $1,500 to $250,000.
  • An energy audit or assessment is required.
  • USDA is not taking grant applications right now and says a new funding notice will publish soon. Guaranteed loans can be paired with a grant, up to 75% of project cost combined.
  • Under the current rules a project must be installed and running 12 months before you apply, so talk to your state energy coordinator early.

Nailbase fit: Insulating the roof of a shop, barn or rural business is the kind of energy efficiency improvement REAP funds. Nothing can be applied for until the next funding notice.


Federal tax credits and deductions

Homeowners, builders, and commercial owners

ENDED

  • Home improvement credit (25C): ended for work placed in service after December 31, 2025. Insulation installed in 2025 can still be claimed on a 2025 return with IRS Form 5695.
  • Commercial buildings deduction (179D): not available where construction began after June 30, 2026.
  • New home builder credit (45L): not available for homes sold or leased after June 30, 2026.

Home Energy Rebates (HOMES and HEEHR)

Homeowners and renters

Not open in these states

These federally funded rebates include insulation, but each state runs its own program and none of the four has opened one. Status for each state is below.

Weatherization Assistance Program

Income-qualified households

OPEN

Free insulation and air sealing chosen and installed by local agencies. It does not pay for a reroof or for materials you pick, but it is worth knowing about. Links are under each state.

Idaho

Idaho income tax deduction for energy efficiency upgrades

Homeowners · Idaho Code 63-3022B, claimed on Idaho Form 39R

OPEN

  • Deduct what you pay to add insulation to your primary residence in Idaho. There is no dollar cap in the law.
  • The home must have existed, been under construction or had a building permit by January 1, 2002.
  • The insulation must be added to what is already there, not replace it.
  • The upgraded part of the home has to meet or beat the Idaho energy code in effect that year.
  • The state's instructions count the insulating material and the labor to install it. Where insulation comes with another product, such as insulated siding, only the separately stated insulation cost counts.

Nailbase fit: good. Nailbase adds insulation over the existing roof without removing any. Have the nailbase and its installation itemized apart from the roofing, and confirm with your tax preparer that the finished roof meets the energy code value.


How to claim

On your Idaho individual income tax return. Idaho energy incentives overview  Text of the law

Idaho Power building shell incentive

Businesses, farms and industrial buildings on Idaho Power

OPEN

  • Ceiling insulation: $0.20 per sq. ft. of roof or ceiling area. Existing insulation R-11 or less, raised to at least R-38.
  • The building needs electric heat and mechanical cooling.
  • Pre-approval is required before work begins when the incentive is $2,000 or more (10,000 sq. ft. of roof).
  • Send the application with invoices within 90 days of completion to retrofit@idahopower.com.

Nailbase fit: good. Idaho Power's worksheet names rigid foam as qualifying ceiling insulation. The finished roof must reach R-38, counting what is there now. Idaho Power does not offer an insulation rebate for existing homes.


Rocky Mountain Power Wattsmart Homes

Rocky Mountain Power residential customers in eastern Idaho

OPEN

  • Attic insulation: $0.50 per sq. ft. in electrically heated homes, $0.10 in electrically cooled homes. Listed for existing insulation of R-19 or less, finished at R-49 or more.
  • Electric heat must serve at least 80% of the home for the heated rate.
  • Apply online within 90 days of completion.

Nailbase fit: ask first. The program's installation manual covers rigid insulation on roof sheathing: the whole roof assembly must reach at least R-20, and it cannot go over a ventilated cavity. The manual does not say which rebate rate that earns, so get pre-approval from Wattsmart Homes before the reroof.


Forms

Idaho insulation rebate details   Idaho installation manual (PDF)   Online application
Questions: WattsmartHomes@rockymountainpower.net

Idaho State Energy Loan Program

Owners of single-family homes · Idaho Office of Energy and Mineral Resources

Closes Dec 31, 2026

  • Loans up to $40,000 at 3% for 3 years, 5% for 5 years or 7% for 7 years. No income limits.
  • A licensed contractor must install the insulation, and a bid goes in with the application.
  • The loan must be approved and closed before any work starts. First come, first served until funds run out or December 31, 2026.

Nailbase fit: ask first. The insulation form lists target R-values for attics (R-49 to R-60), walls, and floors. It has no line for insulation above a roof deck, so ask the program to confirm your roof before applying.


Idaho Falls Power insulation rebate or 0% loan

Homes with Idaho Falls Power service and permanently installed electric heat

OPEN

  • A rebate, or a zero-interest loan repaid on your power bill over up to 60 months ($25 administration charge).
  • Steps: free energy consultation, bids from an approved installer, Notice to Proceed, install, inspection.

Nailbase fit: good. Idaho Falls Power confirmed in writing on November 10, 2026 that insulation installed above the roof deck qualifies under its home weatherization program, as a rebate or a loan for pre-qualified customers. There is no fixed amount per square foot. Idaho Falls Power sets it for each project from the existing insulation, the insulation being added and the square footage, after an energy consultation with an inspection before and after the work. For the zero-interest loan, the contractor must be on Idaho Falls Power's approved installer list. Book the consultation before the reroof.


Start here

Insulation and windows program Call (208) 612-8430.

Avista insulation rebates

Single-family homes in northern Idaho heated with Avista electricity or natural gas

OPEN

  • Attic: existing R-11 or less brought to R-49 or more. $0.75 per sq. ft., or $0.35 for gas-heated homes.
  • Avista accepts R-38 where the invoice shows that is the most the space allows.
  • A licensed contractor must install it. Apply within 120 days with the itemized invoice.

Nailbase fit: ask first. Avista's page does not address insulation above the roof deck. Call 800-227-9187 to pre-qualify before work starts.


Fall River Electric insulation rebate

Existing single-family and manufactured homes with primary electric heat on Fall River Electric (Teton Valley, Island Park, rural Fremont, Madison and Jefferson counties, plus West Yellowstone and parts of western Wyoming)

OPEN

  • Rebates for attic, floor and wall insulation. The amount depends on what is in the home now.
  • A pre-inspection and an energy audit are required before the work.

Nailbase fit: ask first. Schedule the pre-inspection with the co-op's Conservation Specialist before the reroof and ask about insulation above the roof deck.


Enbridge Gas ThermWise

Enbridge Gas customers in southeast Idaho

OPEN

Same rebates, rules, and forms as Utah. See Enbridge Gas ThermWise under Utah.

Not available in Idaho

For reference

No program

  • Intermountain Gas: rebates cover heating and kitchen equipment and new-home builder rebates, not added insulation.
  • Federal Home Energy Rebates: not offered in Idaho.


Income-qualified households can apply for free weatherization. Where to apply

Utah

Enbridge Gas ThermWise weatherization rebates

Enbridge Gas residential customers in Utah, southeast Idaho and southwest Wyoming

OPEN

  • Continuous exterior rigid insulation, R-5 or more: $0.40 per sq. ft., up to $800 for a single-family home and $400 per multi-family residence. Gas heat required. It cannot be something code already requires. No authorized contractor needed.
  • Attic insulation, Tier 1: $0.32 per sq. ft. Add at least R-19 and finish between R-49 and R-60.
  • Attic insulation, Tier 2: $0.08 per sq. ft. Add at least R-11 and finish between R-49 and R-60.
  • Apply within six months of installation.

Nailbase fit: ask first. Nailbase is continuous exterior rigid insulation, but Enbridge does not say whether that rebate covers roofs or only walls. The attic rebate requires insulation between a heated space and an unconditioned one. Email Incentives@thermwise.net with your roof details before the work.


Forms

Rebate table and all application forms   Apply online
Paper forms on that page come in a Utah/Idaho set and a Wyoming set. Mail to ThermWise Rebates, 2223 S. Highland Dr. #E6-333, Salt Lake City, UT 84106.

Rocky Mountain Power Wattsmart Homes

Rocky Mountain Power residential customers

OPEN

  • Attic insulation: $0.10 per sq. ft. Listed for existing insulation of R-19 or less, finished at R-49 or more.
  • Electric heat or central cooling must serve at least 80% of the home. Homes cooled only by evaporative coolers do not qualify.
  • Apply online within 180 days of completion.

Nailbase fit: ask first. Utah has its own installation manual. Ask Wattsmart Homes how it treats rigid insulation above the roof deck and get pre-approval. At $0.10 per sq. ft. this is a small rebate either way.


Rocky Mountain Power Wattsmart Business

Commercial, industrial and agricultural customers in Utah, Idaho and Wyoming

Ask for current offer

The business program includes building envelope incentives for roof insulation on retrofits. The amount changes with each tariff update, so get the current figure and pre-approval before starting.

Not available in Utah

For reference

No program

  • Utah Home Energy Rebates: on hold until further notice. State status page
  • State tax credit: we found none for insulation.


Income-qualified households can apply for free weatherization. Utah Weatherization Assistance Program

Wyoming

Enbridge Gas ThermWise

Enbridge Gas residential customers in southwest Wyoming

OPEN

The same rigid insulation and attic rebates as Utah, using the Wyoming application forms.

Nailbase fit: ask first. Same open question as Utah: confirm with ThermWise that the rigid insulation rebate covers a roof.


Lower Valley Energy insulation rebate

Existing homes with primary installed electric heat on Lower Valley Energy (Star Valley and Jackson)

OPEN

  • The rebate depends on the insulation in the home now and the finished R-value. Current amounts are on the co-op's Weatherization Rebate Chart.
  • Contact the Conservation Department before any insulation work starts.

Nailbase fit: ask first. Ask the Conservation Department about insulation above the roof deck before the reroof: Conservation@LVEnergy.com or 307-885-3175.


Not available in Wyoming

For reference

No program

  • Rocky Mountain Power Wattsmart Homes: no insulation rebate listed for Wyoming. Current list
  • Black Hills Energy: rebates are not available. The company withdrew its 2026 efficiency plan and says it will file a new one. Status
  • Wyoming Home Energy Savings Program: not launched. Wyoming Energy Authority page
  • State tax credit: Wyoming has no state income tax, so there is none.


Income-qualified households can apply for free weatherization all year. Wyoming Weatherization Assistance Program, (800) 246-4221.

Montana

NorthWestern Energy natural gas insulation rebate

Existing homes with NorthWestern Energy natural gas service

Through June 30, 2027

  • Attic or ceiling: $0.45 per sq. ft. going from R-11 to at least R-49, or $0.55 going from no insulation to at least R-49.
  • Materials must be bought and work done on or after August 1, 2026, with the application in by June 30, 2027.
  • Contractor or self-install both count. New construction does not.

Nailbase fit: ask first. The form covers "attic/ceiling" insulation and does not limit the insulation type, but the finished R-49 is a high bar for a roof-deck retrofit. Call (800) 823-5995 and ask whether existing insulation plus nailbase can be counted together.


Forms

Insulation rebate application (PDF)

Mail to NorthWestern Energy, R-EX-NG-I, P.O. Box 1167, Helena, MT 59624.

NorthWestern Energy commercial natural gas rebates

Existing commercial buildings with NorthWestern Energy natural gas heat

Through June 30, 2027

  • Attic insulation: $0.40 per sq. ft., R-11 existing brought to at least R-49.
  • Above-grade wall insulation: $0.60 per sq. ft., none existing to at least R-21.
  • Projects must be completed and submitted by June 30, 2027.
  • Custom incentives through the Business Partners Program are open to commercial, institutional, industrial, agricultural and multi-family buildings.

Nailbase fit: ask first. For a commercial or farm building reroof, ask about a custom Business Partners incentive, which is reviewed project by project.


Flathead Electric insulation rebate

Existing homes with electric heat as the primary heat source on Flathead Electric Cooperative (Kalispell and Libby areas)

OPEN

  • Attic finished at R-49 or more: $2.35 per sq. ft. starting from no insulation, $1.05 starting from R-11, $0.30 starting from R-19.
  • Contact the co-op or submit the form before starting, so it can confirm eligibility.
  • Using an installer from the co-op's list is optional. Qualifying members can pair the rebate with 3% fixed-rate financing.
  • The rebate cannot exceed the installation cost. New construction does not qualify.

Nailbase fit: ask first. These are the largest attic rebates on this page, but the co-op's page does not address vaulted ceilings or insulation above the roof deck. Ask before the reroof: 406-751-1834.


Montana DEQ Alternative Energy Revolving Loan

Homeowners, small businesses, nonprofits and local governments

Open quarterly

  • Up to $40,000 at 3.5% fixed for 2026, with terms up to 10 years.
  • Applications are taken in January, April, July and October.

Nailbase fit: only alongside an energy system. Insulation qualifies only when it goes in with an alternative energy system, such as solar, in the same building at about the same time.


Not available in Montana

For reference

No program

  • Montana Home Energy Rebates: not launched, waiting on federal approval. DEQ status · Sign up for updates
  • State energy conservation tax credit: repealed. It cannot be claimed after tax year 2021.


Income-qualified households can apply for free weatherization. Montana energy assistance · Local offices

Price nailbase for your reroof

Send us your roof dimensions and the insulation level you are after. We will size the panels, give you the R-value and square footage for your rebate paperwork, and quote it.


Request an estimate · Call (307) 690-3864 · Email chuck.pfeiffer@spanels.com · Contact us

Monday to Friday, 8:00 am to 5:00 pm


Change log

  • Nov 10, 2026: Idaho Falls Power confirmed in writing that insulation above the roof deck qualifies for its rebate or 0% loan. Rating changed from "ask first" to "good fit".
  • Nov 9, 2026: Updated the R-value table to the eight foam thicknesses we stock, 2" to 11-7/8".
  • Nov 9, 2026: Added Fall River Electric, Lower Valley Energy and Flathead Electric insulation rebates, and a quote section.
  • Nov 9, 2026: Added the nailbase R-value table, 1-1/2" to 12" of foam, from the foam supplier's published R-values.
  • Nov 9, 2026: Reworked around nailbase reroofs. Added a fit rating for every program, Rocky Mountain Power's installation manual rules for exterior roof insulation, Idaho Power's rigid foam and R-38 requirement, the Idaho Form 39R itemizing rule, and NorthWestern Energy's 2026-27 commercial form.
  • Nov 9, 2026: Page first compiled from each program's own page or application form.


Other rural electric cooperatives and city utilities often run their own insulation rebates. If your power comes from one not listed here, ask them directly.


This page is general information, not tax or legal advice. Rebate amounts, eligibility and deadlines are set by each program and can change or run out of funds. S-Panels Idaho does not administer any of these programs, and no program listed has endorsed nailbase panels.